-
1 custom circuit design
Engineering: CCDУниверсальный русско-английский словарь > custom circuit design
-
2 разработка заказных интегральных схем
Engineering: custom circuit designУниверсальный русско-английский словарь > разработка заказных интегральных схем
-
3 параллельная система ИБП
параллельная система ИБП
-
[Интент]Parallel Operation: The system shall have the option to install up to four (4) UPSs in parallel configuration for redundancy or capacity.
1. The parallel UPS system shall be of the same design, voltage, and frequency. UPS modules of different size ratings shall be permitted to be paralleled together for purposes of increased capacity or UPS module redundancy. The UPSs in the parallel configuration shall not be required to have the same load capacity rating.
2. Parallel Capacity: With N+0 system-level redundancy, up to 2MW of load can be supported by the system.
3. Parallel Redundancy: With N+1 system-level redundancy, up to 1.5MW of load can be supported by the system, and only the UPS being replaced must be isolated from the source (bypass operation is not required for the entire system during the UPS replacement procedure).
4. Output control: A load sharing circuit shall be incorporated into the parallel control circuits to ensure that under no-load conditions, no circulating current exists between modules. This feature also allows each UPS to share equal amounts of the total critical load bus. The output voltage, output frequency, output phase angle, and output impedance of each module shall operate in uniformity to ensure correct load sharing. This control function shall not require any additional footprint and shall be an integral function of each UPS. The static bypass switches shall be connected in parallel.
5. Parallel System Controls: To avoid single points of failure, the UPS system shall have no single dedicated control system designed to control the operation of the parallel UPS system. Control of and direction of parallel UPSs shall take place via a master/slave relationship, where the first UPS to receive logic power asserts itself as a master. In the event of a master failure, a slave UPS shall take the role of master and assume the responsibility of the previous master UPS. Regardless of which UPS is master or slave, user changes to the system status, such as request for bypass, can be done from any UPS connected to the bus and all UPS on the bus shall transfer in simultaneously.
6. Communication: Communication between modules shall be connected so that the removal of any single cable shall not jeopardize the integrity of the parallel communication system. Load sharing communications shall be galvanically isolated for purposes of fault tolerance between UPS modules. A UPS module's influence over load sharing shall be inhibited in any mode where the UPS inverter is not supporting its output bus. Transfers to and from bypass can be initiated from any online UPS in the system.
7. Display: Each UPS multi-color LCD touch screen user interface shall be capable of using an active touch screen mimic bus to show the quantity of UPS(s) connected to the critical bus, as well as the general status of each UPS, such as circuit breaker status information. Any touchscreen display shall support the configuration of the [entire parallel] system and shall provide event and alarm data for all UPSs in the parallel configuration. A Virtual Display Application shall be available for download to the customer’s computer and shalll support remote monitoring of a complete system with up to 4 UPSs in parallel.
8. Battery runtime: Each UPS must have its own battery solution. The battery solution for the entire system can be a combination of standard and third-party batteries, but each UPS must use only one battery solution – either standard or third-party batteries.
9. Switchgear: A custom switchgear option shall be required for parallel operation.
[Schneider Electric]Тематики
EN
Русско-английский словарь нормативно-технической терминологии > параллельная система ИБП
См. также в других словарях:
custom integrated circuit design — užsakomųjų integrinių grandynų projektavimas statusas T sritis radioelektronika atitikmenys: angl. custom integrated circuit design vok. Kundenwunsch Schaltkreisentwurf, m rus. проектирование заказных интегральных схем, n; разработка заказных… … Radioelektronikos terminų žodynas
Circuit bending — Probing for bends using a jeweler s screwdriver and alligator clips Circuit bending is the creative customization of the circuits within electronic devices such as low voltage, battery powered guitar effects, children s toys and small digital… … Wikipedia
Custom hardware attack — The EFF s Deep Crack machine contained 1,856 custom chips and could brute force a DES key in a matter of days the photo shows a circuit board fitted with 32 custom attack chips In cryptography, a custom hardware attack uses specifically designed… … Wikipedia
custom-design integrated-circuit technology — užsakomųjų integrinių grandynų technologija statusas T sritis radioelektronika atitikmenys: angl. custom design integrated circuit technology vok. Kundenschaltkreistechnologie, f rus. технология заказных интегральных схем, f pranc. technologie de … Radioelektronikos terminų žodynas
Custom-Chip — Eine Anwendungsspezifische Integrierte Schaltung (engl. application specific integrated circuit, ASIC), auch Custom Chip, ist eine elektronische Schaltung, die als integrierter Schaltkreis realisiert wurde. Die Funktion eines ASICs ist damit… … Deutsch Wikipedia
Custom Chip — Eine Anwendungsspezifische Integrierte Schaltung (engl. application specific integrated circuit, ASIC), auch Custom Chip, ist eine elektronische Schaltung, die als integrierter Schaltkreis realisiert wurde. Die Funktion eines ASICs ist damit… … Deutsch Wikipedia
Application-specific integrated circuit — An application specific integrated circuit (ASIC) is an integrated circuit (IC) customized for a particular use, rather than intended for general purpose use. For example, a chip designed solely to run a cell phone is an ASIC.In contrast, the… … Wikipedia
Cadence Design Systems — Infobox Company company name = Cadence Design Systems, Inc. company company type = Public foundation = 1988 location = San Jose, California key people = Mike Fister, President/CEO num employees = 5,200 (2006) [… … Wikipedia
Electronic circuit — The die from an Intel 8742, an 8 bit microcontroller that includes a CPU, 128 bytes of RAM, 2048 bytes of EPROM, and I/O in the same chip … Wikipedia
CPU design — is the design engineering task of creating a central processing unit (CPU), a component of computer hardware. It is a subfield of electronics engineering and computer engineering. Contents 1 Overview 2 Goals 3 Performance analysis and… … Wikipedia
Iterative design — is a design methodology based on a cyclic process of prototyping, testing, analyzing, and refining a product or process. Based on the results of testing the most recent iteration of a design, changes and refinements are made. This process is… … Wikipedia
